Forums
New posts
Search forums
What's new
New posts
New media
New media comments
New profile posts
Latest activity
Media
New media
New comments
Search media
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles and first posts only
Search titles only
By:
Current visitors
New profile posts
Search profile posts
Menu
Log in
Register
Install the app
Install
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Firefighter's latest activity
Help Support SkidSteer Forum:
F
Firefighter
replied to the thread
Engine Help Needed
.
probably not they used a perkins 4.108 also in that & i think they made around 40-45 Hp u could probably repair the ford engine that u have
Apr 26, 2024
F
Firefighter
replied to the thread
Joystick does not move easily 940
.
yes i can help u out with parts
Apr 24, 2024
F
Firefighter
replied to the thread
Hydraulic Drive Problem
.
it would appear to be a drive motor fault or possibly a hydro pump that has scarring internally causing a lose of oil pressure when...
Apr 22, 2024
F
Firefighter
replied to the thread
5625sx slow lift and tilt
.
check the pressure at the auxiliaries, im guessing between 2500 & 3000 Psi would be normal Could be the relief valve faulty i think...
Apr 22, 2024
F
Firefighter
replied to the thread
Joystick does not move easily 940
.
The preheat is manual it is a grid heater in the intake 30 seconds when cold is ok, there is no timer or light. the yanmar engine...
Apr 22, 2024
F
Firefighter
replied to the thread
Joystick does not move easily 940
.
u bought a good loader, they are still well liked the t-bar has pivots that can get tight the early models had grease fittings to lube...
Apr 18, 2024
F
Firefighter
replied to the thread
T550 blowing black smoke
.
not to sound stupid, but i had one where the turbo waste gate rod unhooked from the waste gate, no power lots of smoke, also had one...
Apr 18, 2024
F
Firefighter
replied to the thread
Mustang 960 block heater
.
the largest frost plugs on the injection pump side should be 44.6mm, which is 1-3/4 inch, which is usually where they were installed
Apr 16, 2024
F
Firefighter
replied to the thread
mustang 1200 Flywheel / starter problems
.
Rock Creek Consulting, Woodbury Pa. Tim Stine 814-766-3675 Can Fix You Up With Whatever You Need For That Engine
Apr 11, 2024
F
Firefighter
replied to the thread
New owner, old 960
.
Try the filter, the motors may need rebuilt, if the drive is ok in reverse but not forward it would seem as an issue with the motor, if...
Mar 30, 2024
F
Firefighter
replied to the thread
How to change wheel seal mustang 332
.
i do not but i believe the parts are available
Mar 11, 2024
F
Firefighter
replied to the thread
Mustang 960
.
check the fuel supply from the tank, by removing the hose to the filter base, u should get a steady flow . the tank being higher than...
Mar 11, 2024
F
Firefighter
replied to the thread
lift cylinders jammed bobcat
.
I wonder if the seals were damaged during installation, also they had a cushioned cylinder also , i guess the pistons were a direct...
Mar 1, 2024
F
Firefighter
replied to the thread
mustang 940
.
yes they are, biggest issue they had if they sat out in the weather, they had some problems with getting water in chaincase simply...
Feb 29, 2024
F
Firefighter
replied to the thread
Mustang 1200 starter problem
.
is the drive clutch ok, the teeth may be engaging, i had bad drives where the starter functioned ok, but didnt turn engine because of...
Feb 26, 2024
Members
Top